cubcorn36

Reasons Your Fiat 500 Key Fob Won't Work A Fiat 500 key fob allows you to easily open doors and start your car. There are a myriad of reasons why the fob may stop working. www.thekeylab.co.uk includes a dead coin-battery or water damage, receiver modules issues, and interference. This listing is for a NEW replacement Fiat Flip Key Remote that looks like the Ilco brand. It must be professionally programmed (click here to find local locksmiths in the automotive industry). Includes lock, unlock and trunk buttons. Dead Coin Battery A dead battery is the main reason for your 500 key fob being inoperative. Modern key fobs have an operating range that is limited and must be within a few inches of your vehicle to work. If you are not within your vehicle, and you press the keyfob button it will not respond and display the message “Key Fob Not Detected”. If this happens, replace the battery on your coin cell (Part number CR2032) by a new one from a reputable brand such as Panasonic, Duracell, or Energizer. You can find them at the local hardware store or online. After you've replaced the battery of your coin cell It is possible to test it by standing in front of your Fiat 500 and pressing the buttons. The car will flash its parking lights and the key fob will operate the lock and unlock switches. If your key fob still isn't working after replacing the battery, it may be water damage which hinders it from communicating with the module inside your vehicle. Water damage can happen in a number of ways, from an accidental splash to submerging the fob into salt water at the beach. If you believe your fob was exposed to water, you can place it in a rice bag to draw out the moisture. If that doesn't work, your fob is likely to need to be reprogrammed by an experienced locksmith or dealer. Water Damage Damage to the water supply can occur if you immerse the fob in the ocean, or wash it in a machine. Saltwater can cause the circuit board to short, and eventually cease to function. If you get the fob wet, it's not an ideal idea but if you accidentally drop it in the water in a cup or fail to remove it from your pocket before you run the washing machine and you don't have a chance, don't give in. First, remove the battery from the fob. Before replacing the battery clean the electronic chip using isopropyl or a similar product. Check the fob again to check if it's functioning. If the fob doesn't work, it may have to be programmed again. This is usually handled by an auto locksmith or dealer. If your key is older and is not programmed for your car it is necessary to replace it completely. A professional locksmith for cars can carry out this simple task. The locksmith will need the key to be cut to match your vehicle's ignition. They'll also have to program the fob into the system of your car. This is a fast and cost-effective procedure which can be completed within the same day. Receiver Module Issues Your 500 key fob may not work because it's out of range. The remote usually has 30 feet of range or less and if it's far from your car, it won't respond to your commands. This can be fixed by moving closer to your vehicle until it begins responding. If your fob isn't working after you replace the battery inside the coin, which is also called a “button”, “watch” or “button” or “button”, it could be a problem with the internal circuit board. In most cases, reprogramming the fob will fix the problem. You can find directions on how to do this for all automobiles by searching YouTube or looking through the owner's manual. It may be necessary to replace the metal clips that hold the coin batteries in the correct position. If they become loose, it can prevent your coin battery from sitting properly, causing your remote to malfunction. In rare cases the fob might become disconnected from your vehicle because of software or hardware issues. You can fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances, they may need to reinstall the software on your body control module, too. Interference Interference can also cause the key fob to not receive or transmit a signal. This could occur if the keyfob is located in close proximity to a radio transmitter, such as a cell phone or radar detector. The key fob may not work because of a weak connection to the buttons, water damage or damage to the internal chips. If the key fob has stopped working one day without notice, or after trying everything you can do at home to fix it e.g. replacing the battery, reprogramming, and using the spare key fob, it could have a damaged receiver module on your 500. The receiver module is located under the dash, and it picks up the radio frequency signals from the key fob. It then converts them into electronic commands that the vehicle interprets. Fortunately, there's an easy method of resetting all of the on-board systems in your 500 and include the key fob. Disconnect the battery for 15 minutes, removing first the negative cable, then the positive cable. Then, reconnect the battery. This will erase any remaining electrical charge, and then restart the computer of your car. This can help you get your key fob working again. If the problem persists, you should consult an experienced technician. They can identify the exact cause of problems.